Best Car Dent Repair Kit

Kit 26 Sep 2022 10+ Comments Open

1. JMgist Silvery Bridge Puller Paintless

JMgist Silvery Bridge Puller Paintless

It must be used on clean, smooth, flat, non-porous, dry surfaces. Try to heat the dent with hot water or a hairdryer and make sure there's enough strength to lift it, so the effect will be better. Please contact them if you have any questions. The traction pull bridge is an effective dent repair tool. It can be used to repair dents on cars, refrigerators, motorcycle bodies, washing machines, etc. The tabs are 7 different size and can be used for different dents. Don't worry, dent bridge puller won't hurt the original paint or destroy the structure of the car. It is possible to save the repair cost by yourself. Put the screw spin button on the traction rod and slowly tighten until the dent part is flush with the surrounding. The bridge puller sets only have a bridge and 7 glue tabs, not glue gun and glue sticks. The glue gun and glue sticks should be matched by yourself. The bridge puller sets only have a bridge and 7 glue tabs, not glue gun and glue sticks. The glue gun and glue sticks should be matched by yourself.

Brand: Angockoyo

👤There was a small dent in the front panel of the fridge door. There were no creases in the dent. I used a high temperature glue gun with mini Gorilla glue sticks, which were much stronger than craft/hobby glue sticks. If the dent isn't fixed immediately, don't get upset. This repair took me about 15 pulls. Glue will stick to your fridge door and plastic pulls. Rubing alcohol can be used to remove hot glue. The work was done on a small dent.

👤The tool has limited use. It's only useful for larger dents that pop back into place when you pull on them. Think caved in plastic bumpers. You will get 75% to 85% of the way home on those. If you want to pull hail dents that are about the size of a penny with only one side of the dents, a reverse slide hammer type is better. If you have access to both sides of the dent, a body hammer and a swage would be better. Don't try to use this on hail dents, or you'll be pulling your hair out.

👤A dent can be less noticeable with this. You can leave a shallow wavy spot in the metal. A sharp dent can be made less noticeable but still stand out. It is either less noticeable or it is just as noticeable but different.

👤Not perfect, but a very good job. It's not even noticeable anymore. The new refrigerator exteriors are very thin and flimsy, so I don't know if anyone has noticed. The outside used to be thicker and textured. I don't remember any dinging. Follow the instructions. There is a No one will ever notice that there was a ding. Joannie.

👤It take work doing the same thing. There is still something there.

👤The kit did not come with instructions. I think you can't use anything without glue. I have used Pops-a-dent before. This isn't like it. There is something missing here.

👤I used a Goof Off to remove the remaining hot wax on the fender after I let the hot glue set for 10 minutes. If you don't have a strong chemical, it takes a little time to remove wax.

👤It would be good if it were strong. It depends on what you pull and glue.

2. Manelord Repair Puller Double Removal

Manelord Repair Puller Double Removal

It is used to fill holes and provide reinforcement. The Dent Puller item does not include a hot melt glue gun or hot melt glue sticks, so they suggest the user purchase a hot melt glue gun or hot melt glue sticks. It is not suitable for metal surfaces over 1mm. The principle of leverage is used to design the dent puller, and it can be adjusted to fit the dents, the efficient and labor. It's suitable for any dents, repair door ding and hail damage. The action on metal dents is efficient. The package includes a Double pole bridge dent puller, a black tab, a blue tab, a glue shovel, and a black clean cloth. Before using, please read the product description and manual. They will help you solve your issues if you contact them through Amazon. They only service through Amazon, so please do not trust any third-party information. Before using, please read the product description and manual. They will help you solve your issues if you contact them through Amazon. They only service through Amazon, so please do not trust any third-party information.

Brand: Manelord

👤Don't worry, watch the video. Expectation and reality are two different things.

👤I bought it to fix dents on my car. The sliding hammer kit and extra glue sticks were purchased by me. The dent is about 2 inches, but it's gone now. I want to pass on a few tips. Glue won't stick if you apply it while sitting next to the car, and you have to travel 10 feet to get to the car. 2. When pressing the plug to the car, apply lots of glue to cover the whole plug well. 3. Give the glue time to dry. Give it more time if the instructions said 4-5. 4. It pulled most of the dent but left a small hole. I used a small plug to take that out. 5. Most of the glue came off with the plastic scrapper provided with the kit. The rest was taken off with a micro fiber towel. The next step is to remove the big dents from the fender where my daughter hit the garage wall. It is about 4 inches long and 1 inch deep. I might want to use the slider first. Will post updates.

👤The new product design is more energy efficient. The glue is not included in this set, so don't buy it separately.

👤It works perfectly. Simple tool for anyone to use. It is a bonus if you have one. They will give you a glue gun as a free gift if you place an order. Hot glue liberally and glue over the top of the pad for a better grip. Also! It isn't a one and done process. I have been massaging this dent out with glue processes. I will post photos when it is done. A heat gun and a Bondo hammer is a good idea. They will help speed up the process.

👤I used this product to repair a dent on the driver's side door before I returned my car. It worked out well. Highly recommend this product!

👤Acorn hit my car roof. I bought a kit to fix it. I didn't clean the surface the first time, so it took me two tries to fix it. No paint got affected and no stain was left.

👤I received the tool quickly. If you don't have a glue gun, you have to buy it separately. It looks good. If there was a glue gun, I would give six stars. The adjusting system and tensioning is something I like. After using it, I will do more updates.

👤The product is very sturdy and craftsmanship is excellent. It isn't cheap plastic which gives me more confidence that it will hold up. I will try to add before and after pictures of my repair.

👤If you have small dents, this kit will work well. There is a If the dents are larger, I would recommend you buy a T handle. You will get better the more you do, but it really depends on the dent. If it's cracked or chipped, be aware that pulling paint from the body work will make it look worse. How deep is the dent, and does it have curved edges. The temperature on the day of repair will make a difference. Do not expect perfect results. The more time you spend the better. There was a crease in the rear wing of my car. The crease was three inches long on a sloping gradient that was skinned closer to the wheel arch. I couldn't get to the dent from behind to knock it out. Another good reason to use this kit. There is a I started after reading the instructions and watching a video. It was resolved to 75% by my first efforts. A second bout a day or two later achieved a 95 percent fix. I'm happy that it won't be noticed in most lights and angles, but I may do more. It is not perfect. It has saved me money. Hope that helps people with this purchase.

3. Manelord Repair Puller Golden Removal

Manelord Repair Puller Golden Removal

The lightweight is made of high quality steel. The welding systems plastic repair kit will come with a hot stapler gun and a carry case. It is easy to carry. The golden dent lifter with a unique can adjust the level and rotation of the button to better fit the deep dents, it is a scientific design. Any dents, hail damage, door ding and other dents can be repaired with the golden dent puller. The action on metal dents is efficient. The golden dent puller is made of high-carbon and standard steel. The parts of the body contact with high-quality rubber precision package can prevent damage to the original paint. The product is not suitable for metal surfaces greater than 1mm and they recommend user use hot melt glue gun and hot melt glue sticks to work with their dent repair tool. Before using, please read the product description and manual. They will help you solve your issues if you contact them through Amazon. They only service through Amazon, so please do not trust any third-party information. Before using, please read the product description and manual. They will help you solve your issues if you contact them through Amazon. They only service through Amazon, so please do not trust any third-party information.

Brand: Manelord

👤I am a production manager at a heavy collision repair facility in South Florida. I am impressed with the kit. I took a shot and was blown away. The Eastwood kit is identical in its contents to DemtMagics kit which is over $300. The quality is on par. I would be surprised if they came from the same facility. The tabs exceeded expectations. The glue quality is one of my gripes. The black sticks are useless. The yellow sticks work but can lead to over pulling if you are careful. The puller is a great product, fast shipping, and a solid value.

👤I was contacted by Amazon Review Services under the guise that they wanted my opinion on how the product could be improved. I gave some honest suggestions. I was asked if I wanted to get a refund. I said it saves me the trouble of sending it back. I received instructions on how to remove my review, but I still want a refund. I would rather leave an honest review than get my money back. Keep it. If this actually gets published, I hope someone reads it and doesn't make a mistake like I did, either they leave their dent alone or they get it repaired. The Original Review Car is worse now than it was when I started. I got used to it. You are trying to get the metal back into the shape it was in before. I used a lot of hot glue and tried to work out the small dents on our car. I now have a bumpy mess that is more noticeable than the original one. Maybe it works on dents in the middle of a big flat panel. There is no good there. That is not a silver bullet.

👤I bought a car with hail damage and thought I'd invest $35 into this kit. I wouldn't be out much if it was junk. Wow, am I ever surprised? The kit works well. I watched videos on Paintless Dent Repair before I started. The puller is very solid and high quality. It is very easy to use. It has padding on the feet so you don't scratch the paint. The glue sticks supplied with the kit are great at pulling the tab. To avoid over pulling small dents, try applying just a tiny bit of glue and don't let it set up for too long. Get the tab and let it dry for 10 seconds. Pull with a squeeze. You want a quick movement. After the pull, the glue can be sprayed with denatured alcohol. I use the supplied spray bottle, spray 1 squirt, then use my thumb to peel the "puck" off. The tab down tools seem to work well, but I don't have the skills to use them. I tend to get carried away because it's satisfying to pull out each hail dent. I want to pull dents for 15 minutes before I know it's 10 pm. I'm out in my garage and I'm telling myself, "OK, just one more then I'll be done for the night." I can't really say that it's made in the USA because the price is so low. This is an absolute bargain because you get all the components, the high quality of the components, and the crazy low price.

4. Professional Remover Suction Lifting Objects

Professional Remover Suction Lifting Objects

The bridge puller sets only have a bridge and 7 glue tabs, not glue gun and glue sticks. The glue gun and glue sticks should be matched by yourself. The Dent Remover has a rubber bottom that makes it easy to fix dents and objects. The high quality Dent Lifter is made of high quality material and rubber that is strong enough to hold the cup in place. The car dent puller is easy to use and great for moving flat objects at home, great for moving glass, tiles, objects or car dent repair, just simply put the cup lifter on the smooth surface and make sure there is a good suction before lifting. The dent puller cup is designed to be used by one hand and has a precise structure that provides strong suction. If you have a problem with the dent removal kit, please contact them, they will reply within 24 hours. If you have a problem with the dent removal kit, please contact them, they will reply within 24 hours.

Brand: Longten

👤I got a quote from a service that removes dents in cars. $2000. The dent was at least 1/2' deep. I think the cups got about of the dent very quickly. I washed the car, poured boiling hot water on the area, used the big cup first, small cup second, and got the largest crumple removed. I used a tool I got on Amazon to remove the remaining dents.

👤I have never tried to take dents out of my car. The set-up worked well. It's easy to do.

👤My husband worked very hard to get this item to work, but it just didn't. There is a small dent in the ground. It may be smaller, but it also looks like they are more dense because they sucked out small sections and not the entire dent. I think it looks worse than it did when we started.

👤They are scared that they may scratch the paint. I missed the return window. A box is in my garage.

👤This isn't going to take away all of the damage, but it helps. It worked well on my car. Thanks!

👤These are really good. They didn't work for me. The side panel has a crease in it and it wasn't enough to pull the dent out. It was worth a try.

👤What else can you expect for the price?

5. Kaisiking Suction Remover Granite Lifting

Kaisiking Suction Remover Granite Lifting

Before using, please read the product description and manual. They will help you solve your issues if you contact them through Amazon. They only service through Amazon, so please do not trust any third-party information. The suction cup lifter is high quality. The cup pullers are made of high quality material and natural rubber. The rubber pad is soft and won't scratch the paint. The convenience of single stroke pump operation is achieved by the unique design of the Dent suction cup. The pull is not easy to change. The tool is a 4.5 inch cup and a 2 inch cup. The tool kit allows you to remove dents from your vehicle. Make sure the dent is in the flat surface and not the bottom of the cup. Dent is an easy to use tool for moving flat objects. If you want to move glass, tiles, objects and car dents, just put the dent puller on a smooth object surface and pull the handle up. It must be used on clean, smooth, flat, non-porous, dry surfaces. Make sure there is good lift quality. The diameter of the car dent should be larger than the diameter of the bottom of the cup, if it is on a flat surface. The hot water should be poured on the dent area. After pouring the hot water, place the cup on the car's dent and pull it out. It must be used on clean, smooth, flat, non-porous, dry surfaces. Make sure there is good lift quality. The diameter of the car dent should be larger than the diameter of the bottom of the cup, if it is on a flat surface. The hot water should be poured on the dent area. After pouring the hot water, place the cup on the car's dent and pull it out.

Brand: Kaisiking

👤I pulled out the dent on my car. The 60 second video shows how easy it was. I was amazed.

👤In my photos, you can see that someone bashed into my parked car and left a large hole in my number cover. The small cups were the perfect size to pull out the dent. The second photo is the result. The area needs to be heated up first for this to work. I used a hair dryer, but you can also use a heat gun or boiling water. Once the area is heated up, pop on the cups and pull the dents out.

👤I am not impressed. I tried to remove some hail dents and a small dents in the rear quarter panel, without much change. I wouldn't recommend it. Maybe I am not doing something right. I locked the cup in place and pulled it up.

👤I accidentally damaged my clothes dryer by balancing a knee on top of it while changing a light bulb. The dryer works fine despite the dents. I thought I might be able to pop the dent out with a cup. I ordered these because I took a chance. I used soap and water and rubbing alcohol to clean the metal surface of the dryer. The small cups were very strong. The orange cup wouldn't stick to anything. The rubber underside of the cup wouldn't bend in a way that would allow the cup to make a seal on a hard, flat surface, as my husband and I tried multiple surfaces. The small cups were not big enough to pull out the dent, and the orange cup was faulty. The dent in my dryer is still there and serves as a daily reminder for me not to be an idiot and use my expensive appliances as a step-stool.

👤It didn't work to get the dents out of my fridge.

👤I hope I can pull a dent in my car. But failed! On a flat and even surface, it is not possible to have good suction. It should have been called a glass grip. It doesn't hold on to a dent, the small ones are useless, and you have to look for another solution.

👤I accidentally backed my car into the washer in the garage, causing a big dent in the washer and causing problems during the spin cycle. I was able to pull out the dents with the help of the cups. It worked out perfectly. There is a Two small cups were able to hold the washer/metal surface. The larger one needed to make sure that there were no gaps between the cup and the surface in order to create a vacuum. I used a hair dryer and space heater to warm up the metal surface in some videos, but I'm not sure if this technique helps.

👤I bought this to use on my car dents, but it doesn't work, I follow the instructions, but it is not strong enough. Very disappointed.

6. Dintofix Repair Remover Paintless Removal

Dintofix Repair Remover Paintless Removal

You will get a professional service center, 30-day full amount refunds, and quality warranty from Amazon. Customer service is great and will make you feel good after purchase. If you have a question, please contact them. A professional car dent puller and repair kit can be found in the Golden Dental tool set. It is designed to save you money, time and energy by helping you repair car dents and bumps at home. This easy-to-setup tool kit removes dents without leaving any scratches or glue. There is a dental REMOVER tool for all sizes. The tool is used to remove dents from cars. dents of every size and shape get repaired with the help of 12 rubber tabs. The rubber tabs' patterns give you extra grip to lift the dent and get your car back in shape. It is an easy to use repair kit. It has its own glue set to help you in the setup process. The only thing you need to do is set up the kit and use the rubber tab to pull up the dent. The complete car dents tool set includes all the tools you might need to fix your car dents. There is a Golden Dent Puller & Lifter, 12 rubber tabs, a glue gun, and two extra strong glue sticks. A professional dental REMOVAL KIT for cars. It is a professional kit. It is designed to give a strong grip on the surface of the dents. It is made from high quality material. It's smart design makes it suitable for a professional setup. A professional dental REMOVAL KIT for cars. It is a professional kit. It is designed to give a strong grip on the surface of the dents. It is made from high quality material. It's smart design makes it suitable for a professional setup.

Brand: Chefore

👤This was more difficult to use than I anticipated. I was only able to reduce but not remove, then dent in my fender, despite multiple attempts over the course of an hour. There is a short window where the glue can adhere to the body of the car if it is too warm or too cool. I used every tab in the kit to remove a small dent from the fender of an SUV. I read the instructions carefully, but it took a bit of trial and error, and I'm unsure of the exact moment to pull for best adhesion. The end result was an improvement, but the dent is still visible. I probably could have gotten better results if I had more tabs. My experience shows that you should hold the tab on the car without glue and plan how you will position the puller. Make sure the knob is adjusted correctly so the receiver can attach to the tab. When you pull the lever, turn the adjustment screw to grab the tab as soon as you position the puller. Pull the glue when it's still warm but not sticky to the touch. If the tab doesn't pop off, try to use a smooth pull, screw the adjustment screw a little more, and have a bit more leverage. I was trying to pull a fist-sized dent from a small door suck, but this would work better on small door sucks. The puller is a solid piece of equipment, but getting the glue to stick is difficult. The glue did not leave any marks on my paint.

👤This product comes with everything you will need to pull out dents from your vehicle. If you have a deep or large dent, it may not come out as flat as you would like. You have to be patient. It can get frustrating if you don't know how to take dents out. You have to make sure that everything is placed correctly and that you have enough glue. If it's placed too far right or left, you won't be able to get the dent out completely. If you don't have enough glue, you won't have the proper tension to pop the dent. It is an at home kit and will work best on dents that are newer and have no rust. If you are willing to take the time to lay out everything correctly, you will have good results.

👤I tried to fix it, but it was not possible. The thing is made of high quality aluminum. Really impressed with that! The glue gun is cheap and acceptable. I didn't expect the glue sticks to be as strong as the plastic things. I grabbed the stem with pliers and was able to get a little further, but it broke off and I had to use a heat gun to get the glue off.

👤I was contacted by email to review the updated version of the Chefore Dintofix Car Dent Repair & Remover Tool Set. You receive a comprehensive kit with everything you need to pull a dent, when you open the box. The tool puller is made of aluminum. I would have liked it to have longer handles, but it was ok. The rubber-coated, hinged feet are L-shaped and can be slid over. The glue gun has an on/off switch and a metal nozzle. The glue gun dripped until the glue stick melted and it relaxed after being pulled. The tabs were disappointing. The heads of a couple were molded askew. There are three types of tabs; round ones with an aggressive radial pattern, rectangular ones with a slot / holes and oval, flexible tabs that appear to be designed for long, narrow dents, and plain, flexible "wings". One cracked along its crease while looking at the oval ones. These are cheap and nasty in comparison to the tool. There is a The heads and stems of the tabs are smaller than the receiver. It looked like these weren't designed for this tool. The head ands stem diameter is the same on all the tabs. The tool has a threaded nut that allows the receiver to be adjusted in height. The material was very soft and easily peeled off the tabs when I used the supplied glue stick. The glue easily pulled off the surface it was stuck to, which made the dent pulling useless. I used my own gun glue and stick to help reduce some dents in my truck. It stuck better to the surface, but also to the tabs, so I couldn't remove it. If you apply the alcohol to the glue, peel it back, apply more and it will peel off whatever it is stuck to. The tabs were too aggressive and it was difficult to pull the glue on them. The tabs have a permanent layer of glue. You can apply more glue onto that and the glue remnant will stick to the new glue. I tried to use this on my freezer because I didn't have a dent in my vehicles. Some photos were taken on my sink because it was easier to photograph. The smallest round tab pulled a little but didn't have enough surface area to be very effective and pulled away easily. This tool allows you topulse the tab, squeeze the handles a little at first, then more and more, unlike the threaded puller I have. It's nice to be more precise with "working" the dent out. It is difficult to move the tool over the head of the tab and keep the rubber feet from getting in the way. I tried the largest round tab to see how much pull force there was. The glue gave way after the tab became a cone-shape. The tab flexed and pulled on one side after applying glue. It did pull the metal, but not evenly. I'll be using my other puller in the future and not this one. The product falls short with the tabs. The puller is built to last. The tabs are much thinner and the plastic is more smooth than my other tool. My other tool's tabs are much thicker and stiffer, and while they have a pattern, it is shallow and the surface is rougher. Any glue left on it can be easily removed with a spray of alcohol. It's easy to spray and peel off the glue that's left on the bodywork. I see a stronger snap as the glue gives way. The tabs don't flex. The strongest direction for glue to survive is on the glue layer. I'm not sure how this kit has been updated, but there was a card in the package that said there was a new upgraded version, and if I was interested in trying it, email this address. I was wondering if I got the earlier version. Who knows? I didn't have to pay for the kit, but if you improve the tab design it might be worth it.

7. CARTREND Removal Suction Remover Lifting

CARTREND Removal Suction Remover Lifting

Quality technical support, professional service center, 30-day full amount refunds, and great service are what you will get. If you have a question about the car dent removal kit, please contact them, they will give you a replacement or refund. The Dent Remover has a rubber bottom that makes it easy to fix dents and objects. The high quality Dent Puller is made of high quality material and rubber that is strong enough to hold the cup in place. The car dent puller is easy to use and great for moving flat objects at home, great for moving glass, tiles, objects or car dent repair, just simply put the cup lifter on the smooth surface and make sure there is a good suction before lifting. The dent puller cup is designed to be used by one hand and has a precise structure that provides strong suction. If you have a problem with the dent removal kit, please contact them, they will reply within 24 hours. If you have a problem with the dent removal kit, please contact them, they will reply within 24 hours.

Brand: Cartrend

👤The dent can't be pulled out by the suction.

👤You would think that a German product would be made of solid construction. Construction offers peace of mind when under a vehicle. It's a good idea to recommend it.

👤Does as it was designed. Sturdy and durable.

👤Ein volley ist es gute Erweiterung _neben_. Apotheke deponiert! Inklusive, Verbnde und Pflaster. In Plastik, lieblos reingepackt. Keine Folien. Decken. Beatmungstuch ist bei meiner Durchsicht. Wen man den Plastikkoffer das erste Mal ffnet, ghnt. Allerdings finde Ihren Koffer, das bei Pflaster und anderes Kleinzeug, schlecht. The Autoapotheke is located in NORM V 5101.

👤Sicher kein dauerhaftes und stabiles Schloss, aber fr "eben mal abstellen" reicht es aus. Es sitzt wackelig in der Aussparung, aber es schliet und arretiert den Handgriff. Ich vermute, die Steckschlsser die gleiche aussehen. Es passt - und das tut es. Man ist die Reste des alten. I am Wege. Fett ist schadet.

👤Im Vergleich von 6-Tonnen und 2-Tonnen Bcken ist das bestellt. Durch die Standflche erscheinen. Zudem ist die Schnellentriegelung meines Erachtens. Ihren leichtgngige Schnappfalle in Verbindung ist war. Hhe ist das bei dem Kippen evtl. Ich bei 30 cm vonbocken, so viel Platz so knnen. There is a man in this picture Ich ist niemandem, die Herz legen ist, so hatte.

8. Upgraded Version Stapler Knifeļ¼ŒFlat Repairing

Upgraded Version Stapler Knife%EF%BC%8CFlat Repairing

All Inclusive Kit. Everything you need for multiple applications is included in this kit. This is more liquid plastic than most other products. The kit contains 8 grams of flashFix Liquid Plastic, UV flashlight, batteries, and a sanding block. It was made in the USA. The welding repair tool set has a maximum power of 100W, which can help you finish the repair of plastic parts of your car faster. It is suitable for repairing bumper, dashboard, lamp holder, plastic ring, radiator, car and motorcycle plastic device. Repair broken parts and prolong its service life. Strong for shock and twist. The rubber handle is comfortable and will not make you feel tired. It was quick and easy. There are different types of nails. No training is required. You can learn to use in seconds. There are different types of nails. No training is required. You can learn to use in seconds.

Brand: Allturn

👤I put this to work after I got this. There is a large crack in a food dehydrator that has been there for over a year. I melted the crack completely shut by using the spatula looking thing and using the curved stapler to reinforce the crack. I've contemplated throwing this thing away for a long time, but now it should work just like new. My wife pointed out that it doesn't look pretty but it does the job. I had a piece of plastic on my vacuum cleaner repaired. The step on lever that keeps my vacuum upright broke and it wouldn't stay up anymore. I was going to throw it away but after watching four clips it seems like it's holding up. This thing is amazing if this thing works when I pull the Trigger and I can place a staple and repair plastic. We will see how long it lasts. It comes with a case and a lot of staplers. Great value! If you don't put a fan over the project, you will come back smelling like burnt plastic, like me.

👤I bought this because my dash board was cracking. I used this tool to melt the plastic and insert a hot staple in the middle of it. A little tool. It takes about 10 seconds for the orange glow to come on. I am happy.

👤I am very happy with this product so far. It was used to repair a crack in my trash can. It was a very sturdy repair. If you want to pull the gun away, leave the staple in the melted plastic area and let it cool a bit. Eye protection is required when you clip staple legs. If the cut off is still sticking out, a small hammer will flatten it.

👤There are two issues with the gun. 1) The power cord gasket was not inside the housing, which allowed it to be pulled out and cause major issues. I had to remove the handle and put the boot inside. There are two more The light does not work. I was disappointed that the light would have been helpful in helping me fix the piece that was in a dark area. The gun and stapler worked for me and I was able to get two repairs done. One was a piece of metal that held my wife's bumper to the car and the other was a piece of electrical equipment.

👤My first staple was burned through. You don't need to be cautious with it because it gets super hot and fast, but you need to let it cool down or you risk yanking the wet staple out.

👤I think the tool is fairly priced considering that it comes with different staple for different applications. The instructions could have been better, which made me give the stapler 4 stars. I watched a few videos on the internet before my first project. I decided to practice on the cracks after destroying a snow shovel. I figured out how deep and how long it would take to maintain heat.

9. GLISTON Paintless Dent Puller Adjustable

GLISTON Paintless Dent Puller Adjustable

Before using, please read the product description and manual. They will help you solve your issues if you contact them through Amazon. They only service through Amazon, so please do not trust any third-party information. Paintless Dent Puller Kit can be used for any metal surface, but not for corners or creases. A professional Dent repair kit. The Golden dent lifter can adjust more than 1 cm height and more than 3.8 cm width for small and big dents, and 21 different shapes and sizes of pulling tabs are made from PA materials. The Dent removal kit is easy to use, since the accessories of Paintless Dent Repair are not complicated at all. You need three steps to repair a dent. The tab should be full with glue in the dent. The dent lifter is used to pull the dents out. The alcohol and plastic shovel are needed to remove glue. It is suitable for repairing small dents. All materials of their dent removal are paint friendly. The holder bottom of the dent lifter has soft rubber. Glue won't hurt the original paint and can be removed easily. The dent puller kit is made from high quality metal and plastic that will last you a long time. All products passed strict quality control before shipping out, they are professional manufacturer and honest sellers, and they protect the right of the customers. If you are not satisfied with your purchase, they will accept a return. The dent puller kit is made from high quality metal and plastic that will last you a long time. All products passed strict quality control before shipping out, they are professional manufacturer and honest sellers, and they protect the right of the customers. If you are not satisfied with your purchase, they will accept a return.

Brand: Gliston

👤I had to have my vehicle fixed after a couple of door dings. I had an estimate done by a pro and he said it would cost me $450 to get the job done. I couldn't afford it. I started researching on the internet. The tool kit was the most complete one I've seen. It had the highest review on Amazon. I bought a glue gun and tried it on my car. The dime size ding took me 2 hours to minimize. I didn't have the experience or knowledge to take it out. It took me about an hour on the second ding. I think practice makes it better. It was comforting to know that they have a variety of pulling tabs to match the size and shape of your ding or dent, as I was in this kit. The puller was easy to use, but don't use it too aggressively for better results. The rubber feet helped a lot as they protected the paint and kept a good grip on the panel. I haven't used the hammer and tap-heads yet as I still need to learn the basics of PDR. If you care for your car as much as I do, this kit is a great value and will help you save money for the long term. The kit is highly recommended for fixing dents.

👤The package has a lot of "doodads" that look fancy but are cheap. The glue gun works. That is the only thing that works. The glue was not sticking when I tried to pull the ding. I cleaned it with alcohol. I thought I'd try another ding. It pulled the paint off. I still have the ding, but I have a nice big chip in the paint, right down to the primer. Do yourself a favor. Take it to a pro. A lot of places advertise $100 per panel. I'll have to pay at least $400 to fix the big, dime-sized chip that I'll have to live with. Gliston paint less Dent repair kit is cheap.

👤I found a nice selection of hot melt glue sticks, but no hot glue guillotine gun. The glue sticks are for a small glue gun. You have to order the glue gun separately. Not good. The glue gun shown on the item's page was ordered as frequently bought together. The glue gun I already have is compatible with the glue sticks that came with the dent puller kit. It came with its own glue sticks of the same type. I can't say how well this kit works yet.

👤The Gliston was the one I settled on after looking at several other tools. I wanted to try it out on the bed of my pickup that has dents, so I decided to do it. It was a good place to start and practice. The glue gun is so light that you need to hang it from something to keep it from falling over. I stuck the small dent I sized up in one of the pads I got. I made sure I had a good bond by setting it for over 3 minutes. I used a paper towel and windex to clean the dent. I screwed the tool down on the tool in order to get good leverage after it was cooled off. The glue popped when I worked the pull in. About 75% of the dent was pulled out. I changed the pad size a few times. I used a whole glue stick but the tool worked well. If the glue stuck there instead of on the paint, I had to remove it. Since alcohol is in short supply, I used windex, my thumbnail and a plastic tool. The tool works well. The rubber pad on the tool is what I would complain about. If you are trying to pull a dent on a rounded surface, the pad will move on the tool. If you pull on the dent a lot, the rubber could slide off and damage your paint. I gave 4 stars because of that. The manufacturer should make the foot pad out of thicker material. The tool received a thumbs up from me. You will get good results if you take your time. You will pay if you get in a hurry.

10. Paintless Dent Repair Kit Removal

Paintless Dent Repair Kit Removal

There are 1 Glue Gun, 1 Bridge Board, 1 Gold Dent Lifter, 1 LED Refletor Board, 1 Red Mini T Bar, and 5 Black Tap Down. A rubber hammer, a clean cloth, a T Bar tool, 52 Glue Tabs, a mini bag, and a plastic shovel are included. It's easy to rate. The complete operation steps and operation video are included in the car body dent removal kit. There is a notice. The dent puller is only available on thin metal surfaces, not the metal surfaces exceeding 0.04in/1mm. Professional paintless design. Their new dent bridge has a unique arched bridge that can adjust the space and rotation of the button to better fit the dents, and they promise the screw on the bridge won't loose when you use it. There was no damage to the paint. There is a wide application. The dent removal set can be used to repair dents. It's effective on auto, motorcycle, refrigerator, washing machine, etc. The package includes a Bridge Dent Puller, 1x Glue Gun, 7x Black Puller Tab, 1x Glue Shovel, 1x Black Stick, 10x Professional 7mm Yellow Glue Sticks, and an instruction manual. 100% of the time. Please read the instructions and watch the video carefully, if you have any questions, please contact them. Before you go to an auto body shop, try their car body dental REMOVAL KIT. 100% of the time. Please read the instructions and watch the video carefully, if you have any questions, please contact them. Before you go to an auto body shop, try their car body dental REMOVAL KIT.

Brand: Leototo

👤My first one had a break, maybe from shipping. I contacted the seller right away and they sent me a new one before I returned the broken one. That's great service. The new one arrived in great condition. I used this right away and it did a great job, I can't even tell where the dent is now. I had to use a hair dryer to remove the glue from the car. After a little hair dryer heat and no Mark's at all, it came of smooth. I used this to save a lot of money.

👤The product was able to pull out some of the larger ones. I wasn't able to finish after I had to pull out what was left. I should have been able to pull out the last little bit. I did not get it completely flush with the small and large attachments. It helped a bit.

👤I bought this because I was quoted 5k for it. I have used this on dents before but didn't want to spend the money to get it perfect. The glue gun is something I've used for a lot of other things and it has worked out. I don't want to spend a lot of money to fix my porsche SUB, it has 70k miles on it. This will be easy to use and perfect for it.

👤Make sure the glue sticks properly in order to get the best use. Make sure the surface is clean.

👤There were a lot of glue sticks. The glue sticks didn't adhere to the car surface. I was able to pull out a small portion of the dent. I will try again with fresh glue sticks.

👤I can't imagine this product working on a car because it couldn't take dents out of thin metal siding. Use it for what it's made for. It is easy to use and should be used before going to a shop.

👤If you cool the spot with ice, it will contact before you start the pull. It's best to use it in the shade. It works like the one at Harbor Freight. The panel should be flatter like a hood or door.

👤It worked as advertised but didn't pull out the dents I bought. It did not remove all the small dents from the doors and fender.

11. YOOHE Dent Puller Kit Adjustable

YOOHE Dent Puller Kit Adjustable

If you have a problem with the dent removal kit, please contact them, they will reply within 24 hours. Their car dent puller kit has 53 pieces and is a perfect tool for car dents. Golden Dent Lifter puller, Pro 2-in-1 Slider Hammer dent puller, rubber hammer, and other popular tools come with professionally designed pulling tabs that are stronger and more durable. The golden dent lifter has a unique design that can adjust the width and height. The fixed position and distance can be adjusted for different dents. It is possible to repair the dents on motorcycles and fridges if the dent is removed perfectly. There are two ways to use the T-bar slide hammer dent puller. The long T-bar dent puller tool is a labor-saving pulling mode that can be used to repair larger dents. The short T-bar dent puller can be used to repair dents of all sizes. You will have different auto body removal experiences. It's so easy to do. The dent removal process is so easy with their kit. These tool kits are good for professional auto repair people and also good for family people who want to do their own paintless dent repair. Technical support will give you professional service center, 30-day full amount refunds, and excellent customer service. If you have a question about this kit, please contact them. They will give you a replacement or full refund, so you don't have to worry about it. Technical support will give you professional service center, 30-day full amount refunds, and excellent customer service. If you have a question about this kit, please contact them. They will give you a replacement or full refund, so you don't have to worry about it.

Brand: Yoohe

👤I discovered that I would be having a lot of "dings" after my teenage kids took their cars to the high school parking lot. I purchased this kit in order to have all the pieces I might need to deal with the daily influx of damage to our cars. I was impressed by this kit because it had a full range of tools that I might need. The kit arrived faster than promised and the quality seems to be pretty darn good, and I appreciate that they thought through the process of repairing a dent when assembling the kit. The inclusion of a small spray bottle was a great touch as it would not be an expensive additional purchase, but it would have caused me some frustration. I can put the spray bottle in with the kit so that it is always handy when I decide to use it. I wish there were more sticks of the glue included, but this one has enough to get me started, and it's not too expensive when I need to order more. I tried the kit on dents. The results ranged from really impressive to pretty good, depending on the damage to the car. I think I will be able to eliminate the "dings" on our vehicles with some practice. I'd recommend this kit to others and will update my posting later if I find any issues with quality orDurability, but at this point, I'm very satisfied.

👤This kit has everything you need to repair dents, including a spray bottle for alcohol to help release the glue. The skill of the technician was the limitation for me. I had small/medium dents on vehicles that are decades old. I wanted to make them better, but they are not worth a lot of money. If you are willing to pay a lot of money, then get it done professionally. If you're willing to take an adventure to learn, then this kit is 888-739-5110 I used both the slide hammer and the metal pulling tool for my dents because the slide hammer was the only one that could handle them. I was pleasantly surprised that some of the dents naturally wanted to come back into place after using basic techniques. The kit has different shapes and sizes for different dents. The punch and hammer tools were helpful when trying to flatten out areas that may have been over pulled. I was happy with my result, even though I have no experience and the cost of the tools is high. Is my results perfect? No. I wonder if I paid hundreds of dollars for the fix. No! It's nice to have the kit to 888-269-5556 for future dents or friends and family. All of the pros seem to have a board with lines on it that they use to reflect on the finish of the vehicle. If you are working to get a professional result, this would be a good purchase. I would highly recommend.

Summary

What is the best product for car dent repair kit?

Car dent repair kit products from Angockoyo. In this article about car dent repair kit you can see why people choose the product. Manelord and Longten are also good brands to look for when you are finding car dent repair kit.

What are the best brands for car dent repair kit?

Angockoyo, Manelord and Longten are some of the best brands that chosen by people for car dent repair kit. Find the detail in this article. Kaisiking, Chefore and Cartrend are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com