Best Repair Putty Metal

Putty 6 Feb 2023 10+ Comments Open

1. Blue Magic 18003TRI ThermoSteel High Temp

Blue Magic 18003TRI ThermoSteel High Temp

It takes 3 minutes to mold and cure, and 60 minutes for service. The product is called an auto accessory. The package dimensions are 14.732 cms. The country of origin is the United States. The country of origin is the United States.

Brand: Blue Magic

👤I bought it for a purpose. The vendor gave 7. They said to keep the extras at no charge, nice. The mixing liquid had mixed with the solid repair part. Couldn't use any. You have to open it to check it is not visible from the outside.

👤The most important issue of the car is the cracked exhaust manifolds near the front, it is an old car with a V8 engine. I cleaned off the rust as best I could and applied the material to the directions I was given, and so far it is working well. The material was set for a week while I attended to other issues. I needed two jars for my use.

👤This stuff is great. It is strong, durable, and simple. I broke a heat radiating fin on the underside of my bike while I was putting it on a trailer. It looked like new thanks to the high heat paint and a dremel.

👤I had a crack in a cast iron back plate for my wood burning stove, this stuff sealed it well, no issues with direct heat contact, stove at 1200F.

👤My husband tried many different kinds before this one. This one has been holding up well. It has a stinky burning smell at first but it goes away after a long time.

👤I used this to fix my car so it would pass the smog test. It worked well and held for about 2 months, but I needed a temporary fix until I could get a new one.

👤The package was not usable because it was broken and already hardened.

👤It seemed like it was too old to work and it fell off when I got it.

2. PC Products PC Metal Epoxy Putty

PC Products PC Metal Epoxy Putty

At POR-15, they strive to bring the ultimate in rust prevention. The POR-15 is trusted by the professionals. Excellent customer service is one of the things they are committed to. They will do everything they can to make it right if you are not satisfied. Fast curing metal filled epoxy putty stick for appliance, machine, automotive and plumbing repair. Return to service in less than 60 minutes and cure it to a dark gray color. Fix holes in sheet metal, rebuild metal castings and insulate electrical connections. Rapid repair of metal objects such as gas tanks, drums, radiators, doors, tools, and pipes is possible with the use of a substance called Epoxy putty. It takes 3 minutes to mold and cure, and 60 minutes for service.

Brand: Pc Products

👤The two part paste sticks to everything it touches. The fingers and skin. I suggest covering your hands and fingers with plastic food storage bags and wearing fresh bags when making the mixed epoxy putty because it will still be usable. This technique is messy but effective, and most importantly, it allows you to fill a void/gap that you are trying to repair, by using the pack solidly, and keeping your fingers and hands free. I wet sanded the cured epoxy with 220 grit wet/dry sand paper to fix my issues. What a change! The cracked plastic case is no longer a problem. I am going to drill a new hole. When I have more results to report, I will update my critique.

👤St. Patrick's finger snapped off when he fell and I had to try and fix it. I was so nervous to find the right product because it was so small and it needed to be able to stand up to sanding to be able to get it into the right shape. I haven't painted it yet. I'm happy with how easy it was to work with and how well it held up to sanding. This product worked exactly as advertised and I was happy with the result.

👤I've been using this stuff for a long time. It's handy for bonding metal or plastic. This isn't a type of glue or glue-like substance, although it can be used for that in the right applications. It's a plastic-like substance that you can form and shape, and then it's ready to use. I've used it in many different ways. The mount for my handlebars was too big for my bicycle. It was mounted on a bigger handlebar. I used the putty to build up a ring around the spot on the handlebars where I wanted to put the headlight. I shaped and molded the putty using water and my hands, and trimmed the edges with a razor blade. The ring around the handlebars is the right size to fit the mount. The plastic knob on my drill press broke. It's hard to replace an obsolete item. I stuck some of the putty on the arm and let it harden. A replacement knob can be found in about five minutes. I lost the cap for the heat sink compound. I made one out of it. It screws on and seals just as good as the original. You can attach a plastic thingy to a metal plate without using screws or bolts. Press the plastic thingy firmly down onto the metal plate after you've got some of this putty on it. Use a knife to trim away any excess. It's very hard and strong when it sets for 5 or 10 minutes. You have to shape and mold it before it sets, but once set, it's durable. It's water proof and can hold up against various substances. It has a paper thin section that has 100 M.Ohms resistance according to my bench tests. It is easy to clean up metal or plastic with water or alcohol. It should be before it becomes hardened. It is brittle and rigid, so you don't want to use it for something that can bend or move against something else. If you need to, this brittleness makes it easier to remove. You can use a hammer and a screwdriver. A wheel is like butter. You have about 5 minutes to shape and mold it after you mix the putty with the gray color. Before it sets, you can use water or alcohol to round it, and as a lubricant to keep it from sticking to something while you mold it into shape. You can wash it off with soap and water. Use a green scrubby pad after it sets. I wouldn't recommend using this putty for something that requires a lot of weight, like a link in chain, or for something that requires a lot of life. If you want to make art out of a bunch of aluminum cans and plastic bottles at odd angles, then this may be the right stuff for you.

3. J B Weld 8237 PlasticWeld Plastic

J B Weld 8237 PlasticWeld Plastic

J-B Weld can do it for you if you want it to be big or small. J-B Weld can restore it right the first time and deliver superior performance, quality, and results for the World's Strongest Bond. J-B WELD PLASTICWELD. A hand mixable two part epoxy putty stick that is formulated to repair and rebuild various plastic compounds and surfaces. J-B Weld PlasticWeld can be used for plastic repairs on a variety of materials. PlasticWeld is safe for contact with water. PlasticWeld takes 25 minutes to set and cures in 3 hours. The J-B Weld PlasticWeld set is not white. The J-B Weld PlasticWeld has a shear strength of 600 PSI. When fully cured, PlasticWeld can tolerate continuous temperatures up to 250oF (121oC) and intermittent temperatures up to 300oF (148oC). PlasticWeld can be shaped, sanded, drilled and cut. There are applications Plumbing, pipes, plastic, auto bumpers and trim, vinyl surfaces and siding, marine repairs, and fiberglass parts are some of the things that can be done. You can do it yourself with J-B Weld. They can repair and restore it right away. J-B Weld is the world's strongest bond. Repairs and rebuilds any rigid and semi-flexible plastic.

Brand: J-b Weld

👤I am using this to fix plastic panels in a car that have tab sockets missing or cracked. I have found that this plastic is good for shaping thicker missing pieces, but it's almost useless for strengthening an existing tab sockets, because my work was just too thin to use this material. I discovered that the existing tab sockets can be strengthened with epoxy, but it's terrible at replacing the missing material. I have a complete working panel if I use this plastic to form the missing parts and strengthen it and the cracked sockets. I needed both. I like how this material can be sanded and shaped. I am using Gorilla 2 Part Epoxy.

👤I worked the putty and it never hardened. When I contacted the company to see if they had any tips on why it didn't work, they suggested I purchase the product again and clean the surface. I cleaned the surface. Maybe it's good for soft plastic and not hard plastic, or maybe you need to work the putty for 20 minutes. I needed a plan of action to purchase and try again. Buying again seemed like throwing good money after bad.

👤I used this to fill equipment holes in my truck. It was used by the police in Texas and when they removed all the lights, radios, and cameras, it left over 20 holes. I cleaned and filled the holes with this putty after removing all the trim. I sanded them all and prepared them for painting. Some manufacturers have paint that matches the original interior colors of plastic and vinyl. You never knew where the holes were after painting. This is a great stuff that can be sands and painted. I will use this on my next vehicle.

👤My car's smart key broke. I was able to fix it and save $150.

👤This was a pretty good way to fix a plastic bumper. I had to do 3x rounds of applying sand and shape, but I finally got it to be a 7 out of 10. I had some air bubbles. Unlike Bondo, this is hard to form to the dent as you can't sand it after. You have to sand and sand and sand. If you want a permanent fix for a plastic bumper, this is your stuff.

👤My wife hit something solid with the front bumper of her car. The cut was six inches long. I tried to blend it in using regular glue and paint, but I couldn't seal the cut. I realized that the one piece of the solution I had been missing was the J-B Weld PlasticWeld when I saw it. I used white fiber duct tape to cover the backside of the bumper after I pushed it together as closely as I could. I made sure that the duct tape and undamaged edges of the cut were protected by putting the putty into the front of the cut. I probed the putty to see if it stuck to the tape and the bumper after it dried. It was a simple process of sanding it down and applying the proper paint to blend it in. It's done! You couldn't tell if the bumper had been damaged. If you hadn't tried this simple solution, this repair would have caused you to buy a new bumper. I tell myself that thousands of people have solved the same problem before me when I have a problem that I haven't attacked before. Is they smarter than me? Maybe a lot of them. I think about what needs to be done and come up with a plan. If we just think about how to do it, we can fix a lot of things. Chances are that you will learn something from making the effort, even if you don't succeed on the first attempt. Try again with your new knowledge. You will get it worked out after a few tries.

4. J B Weld 8267 S SteelStik Reinforced

J B Weld 8267 S SteelStik Reinforced

No need for mixing or application tools. J-B WELD STEELSTIK. A hand mixable two part epoxy putty stick that is steel reinforced and non-rusting to quickly repair or rebuild anything made of metal! J-B Weld SteelStik is safe for contact with water. SteelStik takes 5 minutes to set and cures in 1 hour after it's set. The J-B Weld SteelStik set is dark grey. J-B Weld SteelStik has lap shear strength of 900 PSI, can tolerate continuous temperatures up to 350F, and is chemical resistant against petroleum, hydraulic fluids and other chemicals. SteelStik can be shaped, drilled, sanded and tapped. There are surface applications. Iron, copper, brass, aluminum, bronze, fiberglass, plastic, and PVC are used. You can do it yourself with J-B Weld. They can repair and restore it right away. J-B Weld is the world's strongest bond. You can do it yourself with J-B Weld. They can repair and restore it right away. J-B Weld is the world's strongest bond.

Brand: J-b Weld

👤It works so far. When the instructions say it will set in 5 minutes, I have to warn you. You need something else if you need longer working time. By the time you kneed it uniformly, you could feel the heat building up and it was starting to set so get moving! Thank goodness. I use it for a lot of things, including making a new N64 controller, fixing a broken rod, and reinforcing a metal tank. I gave it a 3 because it's not like the liquid form. If you're going to use it on a smooth surface, it's better to lock in as a mechanical retention, so it won't fall apart if vibrated or flexed. When it started cooling, it felt like a rock. I put it on the gravel in my front yard.

👤Outstanding! It was easy to use. Not too fast but bonds well. You slice off the amount you need. I think it's the other way around, because there is one grey part putty on the outside and another black part putty on the inside. When you are ready, you start kneading the two parts together. The instructions state that you have 3 minutes to finish working with the epoxy until it's too hard. I may have double that time, but don't count on that. This was used to mold a replacement part. The blade of a folding knife had a broken plastic handle. The instructions state that the epoxy will set in about 3 minutes. I had more time after that. I had enough time to apply the putty and work it into a close approximation of the part that broke off. I had a mirror image to go by from the other half of the handle. After letting is fully set, some grinding with a Dremel tool was all that was needed to get the epoxy to look close to the original parts. It was set to quit. I was able to grind it to shape, but it was much harder than the plastic handle. A small amount of paint. You have to look closely to see the repair. It's mostly visible from the difference in surface texture. Great stuff.

👤This is a very good putty. I've used it for two applications. The oil pan was leaking because of some scratches. I was able to seal up the scratches with this product. It becomes hard after a short time, so you need to work quickly, but it is perfect for use in an area if you don't have a long time to wait. It is bone dry under my oil pan. I used it to fix a piece of plastic that held my throttle cable in place. It was perfect because of the tension on the cable. The glue dried and I had no way of fixing it. I let go of the tight cable after holding the putty in place for about a minute. Highly recommended for any use.

👤I needed to fill a hole in my car. It's easy to work with a lot of time. It's very hard to work with and stiff when it sets. It will feel warm to the touch if you mix the two parts. It is ready to be applied when it becomes the same color. The difference between separated and mixed is easy to see. Everything I needed was there to help my hole patching job.

5. XUDOAI Repair Plastic Ceramic Multi Purpose

XUDOAI Repair Plastic Ceramic Multi Purpose

Set in 5 minutes for emergency or permanent repairs. It is used to seal the leaking pipes after kneading evenly. A variety of materials can be bonded, including metal, wood, glass, ceramics, fiberglass, stone and many hard plastics. It's used for filling and repairing. It is easy to use, just cut, hand knead and apply to the damaged area. The time is mixing evenly. The curing time is 5 minutes to 24 hours. Completely hardened and fixed after 24 hours. The temperature of the product is between 50 C and 120 C, and the rest is kept in a cool place.

Brand: Xudoai

👤The product is garbage. Doesn't work at all! The package starts off hard. Instructions state that it needs to be in place before it starts to change color. You have to make the white and green parts of the same color. It is impossible to do this before hardening. It is like dried out Play-Doh. It is dried and crumbling in your hand before you can mix it. The product has the word "epoxy" in it's name. "epoxy" means sticky, glue or glue. The product has no trait. I would have been better off using my spit.

👤The green colored mixing component was very stiff and difficult to blend, so I had to return and place a reorder. The application window was closing when the two were uniformly mixed. If you have a task that takes more than 10 minutes, you may have to beat the clock.

👤This didn't work out. Is the pipe still leaking?

👤They couldn't come together because of the dry weather. Both of them couldn't use it.

👤No sirve para pintar de otro color. It is not suitable for painting in another color.

👤The product that fixed my curtain pole was a quality product. The sets are like concrete.

👤A hole in a floor tile and a missing bit of trim on a dishwasher were some of the repairs that it said on the tin.

👤This product was not what it was described to be.

👤I have used similar products before. It was easy to get some from Amazon. There is a I assumed the package's weight would be the same as the price elsewhere. It wasn't. The product was mixed up like play dough. Without cracking, it could not be spread thin. It could not be spread thin or smooth because it wouldn't get into cracks. It got harder. There is a You had to apply a big blob that was not water tight. You used more material than necessary and still needed to apply a water tight layer over top. I will use similar products again.

6. PC Products 167779 Two Part Multipurpose

PC Products 167779 Two Part Multipurpose

Colorado won't. FADE TO YELLOW, or SHRINK: It should be formulated to keep it's color and keep it from sagging once cured. Two-part Multipurpose epoxy glue works as a bonding agent, sealant, and filler for a range of indoor and outdoor applications. Many materials are bonds, including fiberglass, wood, concrete, many metals, brick, glass, ceramic, and rubber. Plumbing and masonry cracks can be found as well as oil, gas, and water tank leaks. It fills holes and casts. The application temperature range is 35 to 115 degrees F, and the service temperature range is -20 to +200 degrees F. PC-7 For large and critical jobs, which allow the user to make changes, the user can work for extended periods of time. Overhead and sidewall work can be done with a high "wet grab" or tack of PC-7 Paste Epoxy.

Brand: Pc Products

👤Great substance. It does not dry very quickly. There are a lot of good comments and user reviews about how temperature affects curing time. The instructions should be read. I've used it to fill a chip in my counter top, to patch holes in a brick wall, and to fix plastic parts that CA wouldn't adhere to. I used a clothes pin to hold it in place while it cured. I can confirm that PC-7 does not stick to wax paper. This stuff seems to stick to everything else. I did not remove stars from the review, but I did mention that Amazon's packaging was not up to par. A pound of plastic containers should not be shipped in an envelope. Before cutting the shrink wrap plastic that holds the containers together, make sure you check your containers. One of my plastic lids was damaged during shipping.

👤The truck's drip rail was starting to split, letting water in. The correct repair is to replace the roof of the truck. Not happening. I was looking for an excellent 2 part epoxy but couldn't find it in the quantity I needed. I found this stuff, cleared up the rail with a wire wheel, and applied PC 7 in the crevasse with a gloved finger. A bit of sanding, primer and paint.

👤This stuff is amazing. It's difficult to work with since it mixes to the consistency of a peanut butter but it dries to a hard, permanent repair. I used this to fill in a few holes in a leather helmet, one of them being about 4 square inches. You can't tell the hole was there because of the different color of the dried epoxy. It takes work to cure the cured epoxy. I used an air powered angle grinder and a sanding disk to remove the dried epoxy then hand sanded it. I have found a replacement for JB Weld with this epoxy and am very pleased with it. The cure time is dependent on the temperature and can take up to a couple days to fully harden so it's not really the go to product for a quick job. For the price of two JB Weld kits, you can get a kit that is 20 times the amount of product.

👤I tried this a few years ago and it worked well. It was used maybe 3 times. I didn't need to use it again because I forgot about it. I needed it and opened the bottles. The containers were sealed. I bought the saw around the year 2015. I thought. "eh... Maybe it has a shelf life. In April of this year, I ordered some more. It was almost hard to open the bottles. Wow. It would take more than a tongue depressor to get it out of the bottles. One trying. I got equal amounts of cardboard to mix. It's like trying to stir cement. It will not mix. This was a good experience. I stopped trying to save and just bought the stuff that this brand mimicked. For reference...JB Weld. I found the tubes in the tool room. I got them a decade ago. Still works, guess what? Tra La La.

7. Blue Magic 18003 Temperature Repair

Blue Magic 18003 Temperature Repair

You can do it yourself with J-B Weld. They can repair and restore it right away. J-B Weld is the world's strongest bond. Iron and steel have cracks and holes. The temperature can be as high as 2400 degrees. The strength increases with heat. It fills cracks, holes and pits. It's great for boilers, stove, barbeques, furnace, and heaters. It's great for boilers, stove, barbeques, furnace, and heaters.

Brand: Blue Magic

👤I used this to fix a cracked exhaust Manifold. If the metal is prepared properly, this stuff works well. I used a die grinder to make a rough surface on the metal. I drilled both ends of the crack with a bit. I used a cutoff wheel to cut a grooves along the crack to hold on to. I waited 24 hours to apply a thin layer. After applying a heavy 2nd layer, they waited another 24 hours. I let the engine run for 5 minutes to warm it up and then let it cool. After the first hour of driving, I got a faint smell but it was gone by the time I stopped. It has held up well so far. Most people use a wire brush to clean the rust off. A wire brush is used to polish it and the epoxy won't stick to a slick surface.

👤The product does what it is stated to do. You will need to use all of it at once because it starts to solidify as soon as the lid is removed. Don't expect to use a lot and then return a few days later and use it again. It won't be usable in the container. I used just enough to run a trial test before committing to using it on my main issue. It passed my testing but I had to make the repair after a week. I'm not sure why it hardened so quickly, it was stored in doors that were climate controlled. It should be labeled as needing to be vacuum sealed after opening.

👤The first jar worked well on my cracked yz 85 expansion chamber, I applied layers thick and wide and cured it in the oven, after a spill I ordered another jar. The product is great when it comes not dried out, but it's toss up because of the 3 stars and 2 different experiences.

👤This is not sticky. I tried to get the firebox open by breaking two pieces of the potbelly stove. There wasn't a good way to hold the pieces together. I was going to use it, but it fell apart before I could heat cure it, and I didn't know how to fix it. I'm going to try again, but it's not easy to work with and it's very brittle before heat curing. If I can't get this to hold, I may buy jb weld's high heat product. I'm not happy. I was hoping it would work, but it says it's for repairing cracks not breaks.

👤It does its work on the manifolds. So far 3 months. It's still holding. I make sure to grind out the cracks a little deeper, then mix well, try not to mess it up. I add more to the side of the bead once the first layer is dry. Interesting stuff.

👤I had an overheated Lexus on my car. The exhaust gasket was missing at the top corners at both ends, which was a good sign. After opening up the QuickstEEL product, I sprayed it with a soapy driver, then let it dry before starting the engine. Like a brand new sound. What so ever? It's easy to apply the whole job and get it cleaned and approved in 30 minutes. It is very easy to work with. A product. It's highly recommended to anyone who's experienced a situation like mine that works.

8. Gorilla 4242501 Epoxy Putty

Gorilla 4242501 Epoxy Putty

There are 8 x 3.5 g packs of Sugru in Black and White. The gorilla all purpose stick is strong and versatile. The strength is 1550 PSI.

Brand: Gorilla

👤I like that this thing stuck to anything I put on, but I don't like it. Make sure that you have the shape in mind so that you can stick it to your surface. I had to use my hands to mold it to my surface because it was getting hard in my hands. He wanted to take his time and make it look good. It was my fault that the bruh took longer to set. I think this thing said fast drying. I only used half the tube and the other half to fix what I was working with. If you think this is done in 30 minutes, you are mistaken. It will be done in 2 minutes. The thing dries fast. This thing gets powdery on anything it touches, so make sure you have tissues by your side.

👤Stuff works! I can't get the dinosaur off my head.

👤It works well, but the smell is terrible, my dogs smell better than this stuff, so I took it off the 2 star rating.

👤I had a toilet seat that moved. The nylon bolts that held the seat on were much narrower than the seat mount holes. I filled the holes with the kneaded putty and waited about 4 hours to cure and set it up, the full cure time is 24 hours. I had no problem marking and drilling the correct hole size. I put the seat back in place. I am very happy with this product.

👤The handle of the mug broke in the suitcase as I was going home. I would have preferred to fly back to Hawaii and buy a new one. That is not very practical. Super glue was the first thing I tried. The porousness of the break points was filled in. It did not stick. I couldn't get any other glues to work because the porousness was smooth. I needed a solution that went over the breakpoints. This gorilla glue is compatible with the bill. I attached the broken handle pieces to the mug with the help of the putty. I did not get a smooth surface because it was my first time applying it. It works! The handle is pretty comfortable. I've been careful not to swing the full mug around. I support the bottom of the mug with my other hand to be safe. I don't know if I have to do that, but I'm careful. It is still holding!

👤It was easy to use, but didn't work. We have a small leak in the basement, so we decided to use this epoxy putty to keep it from getting out. The water was turned off, the surface of the pipe was cleaned, and the epoxy was molded around the small crack. You can see the water dripping again within 15 seconds after waiting one hour to turn the water back on. Not worth it!

👤I bought this product to fix a leak. The product is hard to mix, it's gray in color, and it's supposed to patch holes and leaks, but it's hard to mix, it's gray in color, and it's hard to apply. After 2 applications, leaking did not stop. There are better alternatives.

9. Yanyi Repair Plastic Ceramic Multi Purpose

Yanyi Repair Plastic Ceramic Multi Purpose

The temperature of the product is between 50 C and 120 C, and the rest is kept in a cool place. Repairs include pipes, water tanks, fuel tank leaks, industrial maintenance, tool crack repair, flooring, door seams, auto parts, swimming pool ceramic decoration, etc. It is suitable for a variety of materials, including metal, wood, glass, ceramic, fiberglass, stone, marble and many hard plastics. 6 * 5g individually packaged, no need to cut, fill the repair area, can be polished, painted, colored after curing. 10 minutes: Kneading and use are done. The curing time is 10 minutes to 24 hours. Completely hardened and fixed after 24 hours. When exposed to water, high-quality materials do not lose their insulation.

Brand: Yanyi

👤It worked well for patching metal. It is a good substitute for metal. It fills cracks. I placed a second order for another product to fix other metal objects since I have not found another product that works as well on metal. It didn't work for patching the wheel "holder" to the plastic container. The plastic did not adhere to it. The patch fell off when it dried.

👤I need a cheap fix for a leak under the sink. This stuff has been good for a while. Would use again.

👤I have only used it twice, but it has worked great. Glued the key back in the car. It was too expensive to order a new one and reprogram it. I used it on my wooden clothes line holder. Other glues didn't work. The product works.

👤A broken ceramic vase was repaired by me. A turtle's head snapped off. It takes about an hour for it to become rock. Even after washing your hands, it still has an odd odor on your fingers. I would like to have a 55 gallon can of this stuff.

👤I used this product to patch a hole. I placed a blob of this product four days ago. I went out today and it is still soft. The letter is not set up after I followed directions. Don't buy pure garbage.

👤I used this to fix some yard figures. The other was to fix the bunny ear. The other was making a stem from a broken pumpkin. Both items are very hard to repair. Ready to paint.

👤The bricks came loose over the garage door. It was very easy to poke small amounts of this between the bricks. It's nice to have this at the ready for small jobs.

👤The plastic around the ear piece had cracked and I had high dollar headphones. The product was easy to apply. It's not pretty. It saved a pricey set of head phones.

10. J B Weld 8297 HighHeat Degree

J B Weld 8297 HighHeat Degree

You can do it yourself with J-B Weld. They can repair and restore it right away. J-B Weld is the world's strongest bond. J-B WELD HIGHHEAT. A hand mixable two part epoxy putty stick that is formulated to repair and rebuild materials that will be exposed to high temperatures in automotive and industrial maintenance applications. J-B Weld HighHeat is designed for repairs on exhaust manifolds, tail pipes, mufflers, engine blocks, duct work and other high temperature projects. HighHeat takes 1 hour to set and cures in 8 hours after it is set. The J-B Weld HighHeat set is machine grey. J-B Weld HighHeat has lap shear strength of 800 PSI at room temperature and 600 PSI at 400oF or more. HighHeat is able to handle intermittent heat of 500oF and continuous heat of 450oF. HighHeat can be tapped and drilled at higher temperatures. Exhaust Manifolds, Tail Pipes, Mufflers, Engine Blocks, Duct Work, Machinery and other high temperature equipment are used a lot. You can do it yourself with J-B Weld. They can repair and restore it right away. J-B Weld is the world's strongest bond. 3 times stronger at high temperatures. Continuous heat up to 450 degrees Fahrenheit and intermittent heat up to 500 degrees.

Brand: J-b Weld

👤Have used multiple times for the highest heat conditions. If you follow the instructions, it will be a very strong and permanent repair. The area must be clean. If you have a good solvent, clean the grease off first. Attach a wire wheel to a drill to clean the rust off. The metal needs to be shiny. 2. The mini-grinder has a cut off wheel. 3. Cut off the amount that is needed. Rub between your hands like you are rolling a snake. Roll another snake by folding it back. For two minutes, do this over and over again. 4. Take a small portion off and put it on the surface. Press hard. Put it on the surface. Eventually it will stick and not fall off. Do this for the entire area. It should take about a minute. 5. Press and pull the edges inward, then press again. The edges should not pull away. Use a good hand cleaner and scrub brush to clean hands. Let it dry.

👤As a 35 years-plus aircraft maintainer with the Boeing Co., I can attest to the fact that you have to prepare the surface for the glue to work. There is a Sand away any paint or rust that may be on the metal surface. The acetone shouldn't be found anywhere it doesn't belong. After removing the heavy grime, wipe the area with acetone and a clean white rag or Q-tip, only in one direction. Continue with a clean wipe, until there is no visibleContamination on the wipe. There is a Immediately after, use a spray bottle and a clean white rag or Q-tip to wipe the area. Each time, wipe acetone away with a clean wipe. When possible, spray the area and let it air dry. There is a It is advisable not to touch the area with your skin as it will leave oils and affect a good bond. There is a The metal is drawn out of it by acetone. There is a If you use the alcohol on the plastic part, it will not damage the plastic.

👤I regret buying this and putting it on my car because I was hoping it would plug my exhaust manifolds. It went on easy, just roll it into a snake and roll it onto itself for a few minutes until it becomes consistent. I prepared the area by sanding down, grinding, and applying alcohol. 2 hours of preparation and installation. Allow it to cure for almost 28 hours. It would cure better if it was given an extra 4 because of the extra sun and heat. After those hours, it started burning and causing white smoke with a terrible chemical smell. That lasted for 3 days. I wasn't able to drive my car for 3 days. I had to drive it only at night to try to burn it all off and not get stopped by the cops. They would have thought I was catching fire because of the amount of smoke. I attached a picture of how the new exhaust manifolds looked and what I was trying to cover when I did the replacement. Which was the crack on the manifold and where it meets the flange. Terrible product, not meant for high temperatures. The headaches and terrible smell should be taken care of. The money was returned by Amazon.

11. POR 15 49033 Epoxy Putty

POR 15 49033 Epoxy Putty

It's great for boilers, stove, barbeques, furnace, and heaters. Why do you choose POR-15? The rock hard is easy to use and dries quickly. It is strong enough to resist drilling, taping, and painting. It's perfect for repairing fiberglass cracks, holes and breaks, cracked metal, steering wheel crack repair, rust pits and holes. All purpose opiate putty is easy to use and effective, simply roll the two-part formula in your hands or a clean surface until it becomes one uniform color with no visible color streaks. When smoothing, shaping, or mold, their putty responds well to water. Work with it until it is smooth before it dries. Their two-part industrial metal filler formula mixes like clay and hardened like steel. The putty is resistant to heat, cold, fuels and caustic agents. After curing the epoxy putty can be sanded, drilled, routed, screwed, chiseled, surfaced, tapped, sawn, turned, filed, carved, stained or painted. When do I need this? You can use it on classic car restoration, plumbing projects, motorcycles, mechanical projects, and more. At POR-15, they strive to bring the ultimate in rust prevention. The POR-15 is trusted by the professionals. Excellent customer service is one of the things they are committed to. They will do everything they can to make it right if you are not satisfied. At POR-15, they strive to bring the ultimate in rust prevention. The POR-15 is trusted by the professionals. Excellent customer service is one of the things they are committed to. They will do everything they can to make it right if you are not satisfied.

Brand: Por-15

👤It is easy to work with. Cut off the same amount from both rolls and mix them together. Then put it in place. Put some water on your finger tips. It's much easier to work with Bondo.

👤I used this to patch a small rust hole on my Land cruiser. It worked well to strengthen the metal in this spot, and I have not seen any issues with rust returning. Smoothing with water worked well to get a result that only needed minimal sanding to look great.

👤There was a large hole under the hood of my truck. I took the time to remove the fender. I went for it after researching it. It has the same consistency as other sticks. The final cure was impressive. I used release paper and water to form it. Mother Nature has been pouring cats, dogs, and iguanas. I'll let you know if there is H20 in the truck tomorrow. If you have a complete mixture, it's harder to tell.

👤The steering wheel on my car was cracked. It worked well. It took about an hour for the putty to dry. I shaped it. The steering wheel looked brand new after being hurt.

👤I thought of buying this to rebuild my steering wheel on my 49 Ford. I found many pit holes after I started to sand it. SO had to fill the holes. I need a product like this for a job like this. I used it on another application and it worked perfectly. Good quality.

👤Do you want a easy way to do a nice thing? This is it! You can smooth it with wet fingers. When it gets hard. It is good. It is awesome one day later. There are great products and work by Por15. I do not get paid to say that. You want to work on your body? Go get the kit? A little bit of por15 will do it.

👤I have been using this for a long time. I've used it to repair rusted metal areas. The stop rust property is different from other similar epoxies. I have areas on concrete that have been exposed to the sun and weather for 20 years. It's very slow to cure and amazing strength. Gloves are used in a class.

👤This is the material to use for restoring old cars. No heating metal or using a torch helps old metals retain their strength. It was easy to use. I use it to fix the rust on the trunk pockets and floor of my car.

👤The product works well. I was happy with the results. It seems to be very durable. The shipper was used for order sucked. No phone call had to be made to locate the door at the 3rd party depot. The part was not good. Poor quality of service should be warned to the Shipper.

👤The product is amazing. It's easy to work with.

👤It blends in better in Black, but I haven't rubbed it back yet to see the finished product.


What is the best product for repair putty metal?

Repair putty metal products from Blue Magic. In this article about repair putty metal you can see why people choose the product. Pc Products and J-b Weld are also good brands to look for when you are finding repair putty metal.

What are the best brands for repair putty metal?

Blue Magic, Pc Products and J-b Weld are some of the best brands that chosen by people for repair putty metal. Find the detail in this article. J-b Weld, Xudoai and Pc Products are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to